Download our catalog
(1 MB PDF)

 

 


Hammerhead 5
>more info
 

 

ACCESSORIES & INSTRUCTIONS

Lens & Lens Adapter
Installation of the Level
Installation for the Blue Light
Basic Sight Mounting Proceedure
Changing Sight pin Instructions
Fiber Wrap Pins
6" Extension

 

 

Lens & Lens Adapter:

Our Lens come in Glass and Polycarbonate for the 1 3/4" lens with 2x, 4x and 6x power. In the 2 1/4" aperture only the Polycarbonate lens in the 2x, 4x and 6x power.

Addition of Lens & Lens Adapter:

  1. Remove the three screws on the back of the sight aperture.
  2. Insert the supplied O-Ring then the Lens into the Lens Adapter. Next, align the Lens Adapter to the front of the sight aperture.
  3. Install the new longer screws in the sight aperture.
  4. Do not over tighten and do not use lock tite.


Lens & Lens Adapter

Back to top

 

 

 

 
Instructions for installing the NI-035 Level:
  1. Rotate the bubble to point away from the mounting screw.
  2. Insert the bubble into the sight in either slot at any desired location.
  3. Tighten the mounting screw. Do not over tighten.
  4. Adjust the bubble and tighten the screw. Do not over tighten.

 

Instructions for installing the NI-036 Level:
  1. Mount the level to the front of the sight housing using the supplied screw and the brass bushing.
  2. The level housing is machined to the match the contour shape of the sight housing.
  3. Tighten the level screw, (being careful no to over tighten) to match the contours of both the level and the sight housing.
  4. Level should be set after tightening.

Note: See diagram to the right

 
NI-035
  
NI-036

Back to top

 

 

 

 
Blue Light:

Impact Blue light fits the Collector, Bravo, Hammerhead, Cosmic, Air Lite, Fiber Tech, All Terrain and Vortex sights. Also, fits all 1 3/4" and 2 1/4" apertures.

NI-051B

Back to top

 

 

 

 

Basic Sight Mounting Procedures:

  1. Attach the sight bracket to the windage bracket by sliding the elevation bracket either up or down and tightening the set screw. Set the sight at the middle of the bracket.
  2. Attach the assembly from step 1 to the riser mounting bracket and tighten the set screw. Adjust the windage 1/8" left of center shot (for right handed bows).
  3. Attach the final assembly to the riser of the bow by using either of the tapered holes in the bracket with the two screws.
  4. Get close to the target and shoot the first arrow. Adjust elevation and windage as necessary.
  5. Adjust each pin to the desired distance by using the set screws at the end of each pin. Be sure not to over tighten the set screws.
  6. To customize the sight as to pin selection, remove the set screw on each pin and align the pins in the desired order and retighten the screw. Be sure not to over tighten the set screws.

 

Back to top

 

 

 

 

Changing Sight pin Instructions:

Instructions for changing clear Apertures from right handed to left handed.

  1. Remove the aperture from the clamp.
  2. Turn the aperture around so that the pin is facing in the opposite direction (Facing away from the shooter)
  3. Remove the 3 screws from the aperture and pull inner ring from the housing.
  4. Insert the inner ring into the aperture from the back. (The pin will be correctly positioned facing the shooter)
  5. Align the screw holes and insert the screws.
  6. Be careful not to over tighten the screws.
  7. Insert the aperture into the clamp and adjust accordingly.

Note: Reverse the procedure if changing from left handed to right handed.

 

Back to top

 

 

 

 

Fiber Wrap Pins:

The Fiber Wrap Pins that fit the Impact come in 0.040" in Red, Green and Amber. The Fiber Wrap Pins that fit the Vortex and the Orbit come in 0.030" in Red, Green and Amber.

 
NI-025 Red, NI-026 Green, NI-027 Amber

Back to top

 

 

6" Extension:

CNC Machined Extension

 
NI-065

Back to top

 

 
 
© 2005 Impact Archery • Website by Maxam Design